toivo1037
Active Member
I am having radio issues with my T1M set.
History: I have a set of T1Ms I use with a carlson surveyor 2 and Carlson SurvCE 5.09
When I got them after a bit of fiddling, we got them to work well and reliably. After a year or so I wanted to setup my 35w radio as a repeater to the internal 1 watt. During the process we had to narrow band the radio. I hardly ever used the 35w as a repeater, and it really only worked properly briefly. I had a lot of problems keeping connected when I knew it should be easily working. All through this I was able to use Network RTK so it was not a big issue when in cell coverage.
I began having issues with the internal 1w radio about a year ago. Reliability was an issue, and it finally quit connecting all together. I messed with making new profiles in carlson and got it working intermittently again by trying to go back to the original settings I had in the very beginning. I thought I had them all right but things seemed really finicky. It quit working again, and I have primarily been using the system Static & network RTK for quite awhile (which both work great).
I really need to get the radios working again so I can get some work done in non-cell areas. I would like some help getting everything configured again. I would like to go back to the original setup that we had before the narrowbanding and repeater setup. I know the deal with narrowbanding, and I am in an area far outside cities and have literally zero radio interference in my county, so it will not be an issue. I guess I would rather just have everything back working the way it was in the very beginning.
As far as what is working, I am able to connect to the RTK network via cell, and work normally over a network, so the RTK is working. When trying to work base-rover, I setup the base as I did before, and then connect to the rover. It always says autonomous, Latency N/A so I can not be getting the corrections from the base. The antenna light on both the rover and base are lit green, so I should be getting signal. I have also made sure ALL of the settings match, and I can't seem to get the corrections applied to the rover.
(FYI: I thought I copied the previous config file and saved new ones so that I didn't mess up any settings when I was trying new things, however I can't get any of the previous setting files to work properly now.)
I am making sure SurvCE is up to date right now, and will make sure the firmware on the T1Ms is current as well.
What can we do to get everything back up and working? I really miss my operation running smoothly and I am very quickly losing the weather battle here with snow on the ground, it is urgent I get up and running properly soon.
History: I have a set of T1Ms I use with a carlson surveyor 2 and Carlson SurvCE 5.09
When I got them after a bit of fiddling, we got them to work well and reliably. After a year or so I wanted to setup my 35w radio as a repeater to the internal 1 watt. During the process we had to narrow band the radio. I hardly ever used the 35w as a repeater, and it really only worked properly briefly. I had a lot of problems keeping connected when I knew it should be easily working. All through this I was able to use Network RTK so it was not a big issue when in cell coverage.
I began having issues with the internal 1w radio about a year ago. Reliability was an issue, and it finally quit connecting all together. I messed with making new profiles in carlson and got it working intermittently again by trying to go back to the original settings I had in the very beginning. I thought I had them all right but things seemed really finicky. It quit working again, and I have primarily been using the system Static & network RTK for quite awhile (which both work great).
I really need to get the radios working again so I can get some work done in non-cell areas. I would like some help getting everything configured again. I would like to go back to the original setup that we had before the narrowbanding and repeater setup. I know the deal with narrowbanding, and I am in an area far outside cities and have literally zero radio interference in my county, so it will not be an issue. I guess I would rather just have everything back working the way it was in the very beginning.
As far as what is working, I am able to connect to the RTK network via cell, and work normally over a network, so the RTK is working. When trying to work base-rover, I setup the base as I did before, and then connect to the rover. It always says autonomous, Latency N/A so I can not be getting the corrections from the base. The antenna light on both the rover and base are lit green, so I should be getting signal. I have also made sure ALL of the settings match, and I can't seem to get the corrections applied to the rover.
(FYI: I thought I copied the previous config file and saved new ones so that I didn't mess up any settings when I was trying new things, however I can't get any of the previous setting files to work properly now.)
I am making sure SurvCE is up to date right now, and will make sure the firmware on the T1Ms is current as well.
What can we do to get everything back up and working? I really miss my operation running smoothly and I am very quickly losing the weather battle here with snow on the ground, it is urgent I get up and running properly soon.