Search results

  1. Matt Johnson

    Failure to connect with iPhone

    The TCP Base can be configured with Base/Rover. WiFi settings need to be changed in Netview and Modem. The only way to change them through JField would be through the GREIS terminal. I’m not sure which settings you are asking about.
  2. Matt Johnson

    Failure to connect with iPhone

    If you configured the T2 to connect to a hotspot then this is the problem. The T2 WiFi must be in adhoc mode to connect to JMT. Netview and Modem has a Action to automatically configure this:
  3. Matt Johnson

    J-Mate

    The Andriod and iOS RAMS apps currently do not work and need updated. Bluetooth doesn't have enough bandwidth to support the communications between the devices.
  4. Matt Johnson

    DPOS - Galileo, Glonass, GPS

    Currently only the Developer server has Galileo turned on. It can be selected in J-Field DPOS by choosing the DEBUG server and is also available online at https://dpos-dev.javad.com/jca/#/home. Galileo use was disabled in the Production server about 6 months ago because the use of Galileo was...
  5. Matt Johnson

    Sigma - RTK - NMEA messages

    Yes, it is important to have the right antenna model selected.
  6. Matt Johnson

    Sigma - RTK - NMEA messages

    The problem is still the same, GPS satellites are only tracking CA. Is the receiver connected to the internet with TCP Server enabled. If so, we can connect to it and find the problem. We could also connect to the PC it is connected to with J-Support.
  7. Matt Johnson

    Sigma - RTK - NMEA messages

    Most of the parameters in the receiver are reset to their default values when the firmware is updated or when the NVRAM is cleared, the exception is the Networking parameters which are not reset. .tcl script files are used to save and load stored parameters.
  8. Matt Johnson

    Un-Pair Triumph 2 from HPT435BT

    Pairing through J-Field is only working in the Testing brach right now I believe. You can pair through Netview and Modem to port B.
  9. Matt Johnson

    Un-Pair Triumph 2 from HPT435BT

    Try turning the T1-M off and back on again if you did not do so after pairing it.
  10. Matt Johnson

    Un-Pair Triumph 2 from HPT435BT

    UHF Configuration in Base/Rover Setup and then select the external radio.
  11. Matt Johnson

    Un-Pair Triumph 2 from HPT435BT

    The serial cable came with the radio so you should not need to order it. The USB cable may or may not came with it depending upon when you purchased it.
  12. Matt Johnson

    Un-Pair Triumph 2 from HPT435BT

    You have to connect the modem to the PC using the serial cable.
  13. Matt Johnson

    Un-Pair Triumph 2 from HPT435BT

    Depending upon when you bought the HPT435BT it may have only came with the serial port cable. If this is the case you would need to use Netview and Modem to unpair the radio.
  14. Matt Johnson

    Downloading all Base Files as KML for Google Earth

    Points processed with DPOS are shown in a Google Earth Private Map at https://app.javad.com/jca/#/dpos/pmap. Have you taken a look at it?
  15. Matt Johnson

    Coordinate System Menu

    Yes I think this tab is needed. I still think it should be called Favorites, similar to how Justin has Favorites.
  16. Matt Johnson

    Coordinate System Menu

    I understand your point but the names become very long with the dates append and the only place the full name is visible is in the blue information panel. Here you can see the transformation and epoch so if the user is looking at this they should know the parameters of the coordinate system...
  17. Matt Johnson

    Coordinate System Menu

    Hi Vladimir, I think I have a simple solution that will make everyone happy. When importing a project archive coordinate system will still be given a new ID but leave the name unchanged and do not append the timestamp to the name. The timestamps are cosmetically displeasing and do not help...
  18. Matt Johnson

    Coordinate System Menu

    When a project is imported from a project archive, it creates a duplicate copy of the coordinate system with the timestamps. I agree that it is an annoying issue. Maybe @Vladimir Prasolov and @Andrey Zhiganov can look into fixing this so that identical coordinate systems are not duplicated...
  19. Matt Johnson

    Sigma - RTK - NMEA messages

    Yes, clearing the NVRAM is an option in Netview & Modem under the Actions button. The firmware should still be updated. Note that that NVRAM is cleared during the update process.
Top