Search results

  1. Shawn Billings

    We need the ability to do a full clone of the ls

    Matt is correct, this is the tool to use for matching a new receiver to an existing receiver. There are some settings particular to each receiver that will not migrate.
  2. Shawn Billings

    We need the ability to do a full clone of the ls

    The base is paired to the radio. The LS is not.
  3. Shawn Billings

    Old rtpk vs. New rtpk

    RTPK Usage. I think it also controls the tolerances for RTPK agreement, but @Alexey Razumovsky will know better than me on that.
  4. Shawn Billings

    Old rtpk vs. New rtpk

    Also check your settings for RTK/RTPK agreement. They might be too tight. I'm using 0.2' and 0.3'.
  5. Shawn Billings

    Three Things that we need

    Matt has a good point regarding 3. Name the alignment and save it to a particular page if you wanted to make selecting it from a short list easier. Regarding 2, Matt's point is good, however the CAD tools aren't mature enough to make this viable with a curve, in my opinion. Also, point...
  6. Shawn Billings

    WHITE BOXES DISAPPEARED

    In the action screen, click on the top center button (the one that shows the tilt and compass values).
  7. Shawn Billings

    WHITE BOXES DISAPPEARED

    Are you on current release version? It's on the bottom left of the Action Setup screen.
  8. Shawn Billings

    WHITE BOXES DISAPPEARED

    Look for "Show inner buttons" in your action profile. It's a checkbox that turns on/off the white boxes.
  9. Shawn Billings

    Want RTPK Instruction Video

    There are several videos out there I think, but the application has changed several times so it isn't exactly as it appears in the videos. I'll see what I can put together for you.
  10. Shawn Billings

    Victor Fixed ??

    @Alexander Khvalkov can you suggest what firmware should be loaded for the Triumph 2 as an RTK rover
  11. Shawn Billings

    Victor Fixed ??

    I think the firmware is wrong for Triumph 2 as an RTK rover.
  12. Shawn Billings

    Changing rod height?

    Nate is correct. If you're using arrows at the bottom of the screen to go to the next point, edit it and arrow to the next point then the changes won't take. You must ok the edit and return to the point list.
  13. Shawn Billings

    Internal cell modem

    Only GSM (AT&T)
  14. Shawn Billings

    Where is the T-3 forum?

    External power input for Triumph-LS is 10-30v DC per data sheet External power input for Triumph-2 is 10-16v DC per data sheet
  15. Shawn Billings

    Where is the T-3 forum?

    Nate, I'll get in touch with the Javad office this morning and see what we need to do. I hate to hear that happened. Shawn
  16. Shawn Billings

    Release 3.0.11.802

    I noticed that reset tracking was set to 75 seconds. I would disable reset tracking (set to 0).
  17. Shawn Billings

    Solar Flare

    Try disabling Galileo during these periods to see if your performance improves.
  18. Shawn Billings

    Where is the T-3 forum?

    Try FedEx tracking. Not much we can do about it after it leaves the factory.
  19. Shawn Billings

    Release 3.0.11.802

    Press Setup hardware button 2 times, then RTK DGPS, then Advanced RTK settings, click on Engine 1 and change Reset if far from STDL to 50. Apply to All to change other engines.
  20. Shawn Billings

    Release 3.0.11.802

    Also, check in Advanced settings (press settings hardware button at bottom left of receiver 2 times). Go to GNSS>Systems and Signals Tracking and make sure those signals are in white (that they are being tracked by the Triumph-LS Plus).
Top