Search results

  1. giulio

    Sudden Loss of Workable Fix in Open

    Even today, engines with glonass do not fix. It is strange but it seems that more satellites less fixings, what will it be due to?
  2. giulio

    Sudden Loss of Workable Fix in Open

    I also tried 13 satellites open sky between gps and glonass fixed and after permanent float. I tried to deactivate glonass on 2 of 4 motors and those two deactivated fixed, also deactivated the third motor and this too fixed, the only float the one with glonass
  3. giulio

    Correct height rtk and post process with Rtklib

    Yes in rtklib I checked and the antenna corrections are applied correctly, the statically elaborated point is the c1002 which in rtk and rtpk provides a share of 446.40 in rtklib with antenna application file JAVTRIUMPH_LSA.atx provides a share of 446.246 (which is the right one for the point in...
  4. giulio

    Correct height rtk and post process with Rtklib

    Right I inserted the JAVTRIUMPH_LSA_NONE.atx file and the ellipsoidal dimension has been corrected. On the other hand, the rtk quota is offset by about 11 cm as if this correction were not applied
  5. giulio

    Correct height rtk and post process with Rtklib

    For rtk surveys, the height to be entered is the one read by the rover pole (if no other adapters are mounted), for RTKLIB static surveys at this read height I should also add that of the phase shift of the phase center which, if I'm not mistaken, is 11 cm, right
  6. giulio

    Release 3.0.11.802

    Try them all. I think it's a problem with my receiver. With the old one (navcom sf3040) video file with the comparison tried immediately after, in the same position, indeed resting on the ground, immediately fixed.
  7. giulio

    Release 3.0.11.802

    open sky the motors have fixed (all green indicators) and then when I pressed start all orange
  8. giulio

    Release 3.0.11.802

    RAMS connected sn: 00671 coll roncone
  9. giulio

    Release 3.0.11.802

    Same thing today I am attaching the project with raw data
  10. giulio

    Release 3.0.11.802

    Try them all (reset tracking 0) (reset if from to STDL 50.0) I can't get over it. The engines never start in fix, neither with gps only nor with Galileo, I am attaching raw data recording without rtn connection to understand if it is a problem with my receiver I could try to reset everything
  11. giulio

    Release 3.0.11.802

    changed parameters same result
  12. giulio

    Release 3.0.11.802

    I have just enabled the connection to a new station with galileo and l2c gps, the distance is 54 km, logically I did not think it fixed but at least a float solution yes. First I got the "far from STDL" message. Then the engines started with the different frequencies separated for each...
  13. giulio

    Release 3.0.11.802

    Retried today with a closer station (6 km) gps and glonass, I was unable to stare in the open. These are the various screenshots.
  14. giulio

    Release 3.0.11.802

    Yes, the tracking signals are all with white boxes (except E5aBoc and B2eaBoc) I asked the Trento network for information, but they didn't know either. However, they will enable me in days to connect to a single new station (50 km from me) which also has galileo and I will verify Thanks
  15. giulio

    Release 3.0.11.802

    Yes, as written before, broadcasting is only gps and glonass. So rtcm 3 is fine, but I don't understand why I can't select l2c, l1c, L5
  16. giulio

    Release 3.0.11.802

    Today with more satellites I was able to fix, however the 4 motors always have only the A and D frequencies (both gps and glonass)
  17. giulio

    Release 3.0.11.802

    I don't think it depends on the time but on the corrections I receive of the rtn network which seems to be only C / A and P2 (for 6 common gps satellites) (no l2c, p1, l1c, l5). I do not understand why but the frequency table has been changed, the letters no longer correspond and even the...
  18. giulio

    Release 3.0.11.802

    In the sense that the RTN network does not transmit L1c, L2c and l5? It seems strange. Even more strange that I was unable to fix in the area with open sky, where with the Navcom Sf3040 I have never had any problems.
  19. giulio

    Release 3.0.11.802

    I have recently received my LS + unit, latest firmware. Waiting for the regional network to be implemented with Galileo and Beidou, I am using it in RTN with Gps and Glonass corrections from a distance of about 18 km. The connection is good and there are no delays. Yesterday I had problems with...
  20. giulio

    variance covariance matrix

    Thanks Vladimir and Andrey, I agree with you the error ellipse is much more practical and immediately understandable.
Top