Search results

All other sounds are fine. Only J-Tip is silent. It's got me a little bumfuzzled! N

No more sound out of the LS. I have: Disconnected, and Re connected. Forget and re connect. When connected, and on the screen, the numbers change, as I move, or rotate the J-Tip, and the Blue light on the J-Tip is on. It for SURE is connected via bluetooth. But, NO SOUND. Any suggestions...

OK, Actual elev of the final rod and washer is 1309.421' Actual elev of the CPS is 1309.661' Prev Surveyor's HI is 5.392' Now, how do I change the HI, on a base, and update things? I entered a slant height of 6.37', and used that in the field. (Assumed that the elev was good). Thanks! N PS...

Story goes like this... I got a file from another surveyor. In SPC - Elevation given is 1315.053'. I found his base site. Due to erosion, I decided to LOWER his base site. So, I replaced his CPS with a "Rod and washer" And, lowered it 0.24', from his height. I measured to the CPS 6.37' Slant...

Fire the guy that tipped it over. .... Grin...

I cannot help you with anything, Maybe some antacid would help.....

I don't work for Javad, and I don't have ANY behind the scenes knowledge. However, "Logic" and Nate's imaginations says that it's a system, that downloads from MANY GPS systems, all over the world, which are located in Colleges, and Roof tops all over the world. It all comes together, in...

There is a setting somewhere... That allows the 2 second corrections rate, to extrapolate the 1" missing data, and it works well. I set it, and can't remember where it is. I'd guess it is in radio settings... but don't remember....

I have to agree with: I use 2 second mode all the time, and don't have this problem. ALTHOUGH... I PREFER 1 second mode. But, that reduces my range. And makes more heat. So, IF I could get full internet corrections, it would be better. But, that has not worked for me, in my area. Maybe in the...

EVERY time you occupy a KNOWN coordinate, with your base, you MUST select the correct coord, and assign it. IF you don't it can allow DPOS to move it around a bit. I kinda learned this the hard way.. N

Reference to Ken Larson's Post right above..... This is a VERY important issue, that NEEDS to be understood. Base set up on autonomous location. It is wrong by say 6'. While on the job, user switches to HOT SPOT, and sees a 6' jump. Suggest: Use hot spot, to set up base coord. This should solve...

I second the motion here. MANY times, I want to inverse from the 1st pipe I shot, to the rebar I just shot. This would help alot. I know the description, but not the point number. Nate

Not Yet. I don't know of any advantages yet. (There may be), but I don't know about them. Nate

I think the user fundamentally is not understanding the importance of the BASE station, being ASSIGNED and REMAINING the same, throughout the "Survey". My flow chart is: 1st time on the base, it is based upon a "here". Autonomous source. This typically results in a location, within 7 feet of the...

There are a number of ways to do this. But, this is the one I use most often. Hit the STAKE button. Hit the button right below START. (It usually says POINTS). Here, you are going to get a menu, with 5 option buttons at the top of the screen. These five are labeled: Points, Lines, Alignment...

One difference I can see between the panels, (If I am reading it right) is that Point 1.2 is on PAGE0, and point 1.9 is on PAGE5. The GIVEN SPC values are nearly the same. So, MAYBE the localize is changed for one page, but not the other? N

Cute Hat is a dollar store flexible cutting board mat. I have tied it on top, to keep the precipitation from hitting the screen, and giving false input. I am TOLD that if radiation will heat it, then it blocks and modifies the signal. IF not, then it does not. So... Put your selected "Hat" into...

I guess I WONT be moving up to the latest version. Why Javad and company abandoned this is beyond my comprehension. Nate

I was out in it yesterday. Just a few pics.

No.... And I'm not planning to... for a little while. WHAT do I gain, by moving up to it? I'm waiting for all obvious bugs to surface first. There was a bug in trajectory, and I am VERY glad it did not get me. (Because I was delaying my move up to latest release). Back when there was an...