Search results

I am trouble collecting a trajectory. I have successfully used trajectory a bunch in the past, and I'm not sure what I'm doing differently now. When I press Start T., J-Field shows Fixed for the first shot, then changes to CDF for subsequent shots, and the number of satellites drops...

Does enabling correction services on the fly not work anymore? I started a project using TCP corrections and found I was in a place with spotty cell signal, so I tried to start UHF corrections without stopping the base. The remote base screen just says "Waiting...". I checked all the UHF...

I did a job yesterday that made two short base files on the same point, and I want a single set of coordinates for the base. I started the base the first time with an autonomous position and worked for a little over 2 hours. A thunderstorm came up and the weather service was predicting 2-inch...

I had to do a resection yesterday to get a shot on a rebar that was in a really difficult place. I clicked on the result point button at the bottom of the resection screen and this screen popped up. Could the Code Attributes screen be made to look more like this? I really like the larger...

...should not be allowed.

I have a customer requesting a datasheet, operating manual and date of manufacture for a green LegAnt base antenna. The searching we have done so far has not turned up anything useful. Can someone point us in the right direction? Thanks.

I have made a few modifications to my Triumph-LS+ that I have found useful. I wanted to present them here in hope that someone else might benefit from them and also that they would be further improved by this ingenious group. My Triumph-LS+ came with this orange GSM antenna and this...

I worked on two projects yesterday. When I stopped the base on the first project, I selected Stop and Download. I wandered out of Bluetooth range and the base got disconnected before it finished downloading. The Connect button turned green but I clicked Done and powered base and rover off...

I started a new job today that covered several square miles of rough terrain. Some points had no cell signal but were within UHF range of the base. Others were just out of UHF range but had cell signal. The base was on a new control point so I wanted a long duration base file for DPOS and I...

In setting up my T3 to transmit corrections via UHF with the internal radio, I noticed that the antenna impedance match is pretty poor. (2-4 dB return loss) I tried 3 different antennas with right angle SMA connectors, all with similar results. I think much of the problem is the T3 case being...

The interference icon on my new T-LS+ says 63. The T-LS sitting next to it on the desk says 14. If I take them both outdoors, the T-LS says 3, but the T-LS+ still says 63. I've had it a couple weeks now and I've never seen anything but 63. Both units have apparently identical Spectrum...

Is the RTPK Environment Category available as a white button? If not, it seems to me a good candidate for one. It takes 7 clicks to get there and back and it is something that changes from shot to shot.

I generated a handshake key and when I press Establish Connection I get this message. SN976. It's on RAMS now.

I have a 4-foot discrepancy between RTK and RTPK coordinates that I'm having trouble understanding. I sent project Scott White to support (SN229). I was about a mile from my base, but down in a valley and at the edge of cell coverage. Skies were completely unobstructed. I had no...

Eugene mentioned in another post about colorblind users and re-design of screens and buttons. I like that the distance to last button changes to a green background when the distance to last is small, but I have a hard time reading yellow text on a green field. The black buttons have yellow...

I see it in the UHF settings.

There have been a couple threads recently about migrating settings from one LS to another. My LS had to make a return to the factory (no, it didn't get upgraded to LS+) so I have recently been through the process of transferring everything to the loaner unit and back. I made some notes on the...

What is the meaning of the red stripe on the UHF icon?

What is the difference between un-checking the Apply Shift checkbox and pressing the Undo Shift button?

I can connect Net View & Modem 2.2.5.4 to my Triumph 2 via TCP. The Triumph 2 is connected via WiFi to my Verizon Jetpack that has a static IP address. The Net View & Modem TCP address is set to the static IP address, Port is 8002, and Password is set to the Jetpack Password. I have a second...