Search results

  1. Vladimir Zhukov

    NGS SPCS2022 Coordinate Systems (Alpha)

    Hello Shawn, Thank you very much for a valuable information provided Regards, Vladimir
  2. Vladimir Zhukov

    DPOS temporary outage

    DPOS is running. Thank you very much for your patience, Vladimir
  3. Vladimir Zhukov

    DPOS temporary outage

    Dear customers, We regret the inconvenience caused by the interruption of our DPOS service. All at JAVAD appreciate that free post-processing is a valuable feature for our users and the unavailability has changed your usual workflow. Our team is working diligently on restoring the DPOS...
  4. Vladimir Zhukov

    Is T2 capable of TLS connection to NTRIP broadcaster?

    Hello Steve, This option will be supported soon Regards, Vladimir
  5. Vladimir Zhukov

    Our green T-2 tops are failing - HELP!

    Hello Nate, Good point, thank you! We will add Triumph-2 Seal Gasket to the kit. Regards, Vladimir
  6. Vladimir Zhukov

    Our green T-2 tops are failing - HELP!

    Some guidances to the Triumph-2 Top Cover Replacement are available from the link
  7. Vladimir Zhukov

    Our green T-2 tops are failing - HELP!

    Hi Nate, Shawn is right, it could be a little tricky. We will see what could be shared. Anyway if you already touched a battery it means you went successfully via the process once !! :) Regards, Vlad
  8. Vladimir Zhukov

    Our green T-2 tops are failing - HELP!

    Hi Nate, Hi Jim Your feedback about the experience of using TRIUMPH-2 is very much appreciated! The latest revision of the top cover of TRIUMPH-2 made from new improved material, which was intensively tested for hard conditions before release and shall suspend environmental conditions, shock...
  9. Vladimir Zhukov

    TRIUMPH3

    Hello Michael, Operation Time is more than 12 hours on one full charge, but it depends on the operation mode of Triumph-3. The most battery consuming mode will be the GNSS base mode with 1 W UHF transmitting MSM corrections. Such a mode could consume fully charged new battery within about 8...
  10. Vladimir Zhukov

    T1M Upgrade

    Yes, you are right, Shawn. Only TRIUMPH-3 base GNSS status is supported correctly in the current J-Field version. Just ignore and move click by Start Base
  11. Vladimir Zhukov

    Good news

    The following serious limitations of BDS/GAL in Triumph-2 should be considered: TRIUMPH-2 utilizes the only single-frequency capability of BDS and GAL tracking and yes, using of single frequency BDS and GAL could improve performance versus to GPS + GLO only, but the level of improvement is...
  12. Vladimir Zhukov

    Good news

    Few more comments based on working with Nate's T2: 1) make sure firmware is at least 3.7.9 (latest for today) 2) update OAF from the web to assure you have the latest one with BDS B1C enabled. Very old OAF enabled B1 only. The latest OAF will enable also BDS B1C and GPS L1C 3) B1C signals are...
  13. Vladimir Zhukov

    Good news

    Hi Nate, Thank you for giving access to your receiver. You had firmware from 2017 and OAF with not enabled BDS B1CI It should be ok now
  14. Vladimir Zhukov

    Good news

    Hello Nate. It would be good to check settings of your T2 remotely if you are ok with an idea, then 1. Download JSupport program from the link: http://get.teamviewer.com/javadgnss 2. Run the program from PC, connected to the Internet. 3. Wait some seconds until red cross in the program...
  15. Vladimir Zhukov

    Good news

    It seems you did not enable it in all places. please confirm for BDS system signals B1 and B1C also checked in N&M?
  16. Vladimir Zhukov

    Good news

    Hi Nate, are you looking still T2 sky plot in Netview&Modem or already in J-Field?
  17. Vladimir Zhukov

    Good news

    Hi John, it looks like some issue of J-Field representation maybe because this is an unknown configuration for software. This could be corrected later. Just ignore this info and start your T-2 base, initially two engines RTK did not use BDS and GAL, but after a long click on the Reset Engines...
  18. Vladimir Zhukov

    Good news

    You have already BDS in tracking! Congratulations! see you satellite tracking tab
  19. Vladimir Zhukov

    Good news

    Also for your information: sending to receiver %% or %HELLO% or %set,/par/l1center/frq,1571% will not be accepted by the receiver as a command. such sequences are just used to test the connection from PC to receiver. for example, when sending %% receivers returns RE002%% %HELLO% returns...
  20. Vladimir Zhukov

    Good news

    Hello Nate, Your receiver s/n 00728 utilizes mainboard rev. 6 if you successfully applied a shift, which is needed for your revision, just check that BDS and GAL are enabled for tracking and use in a position
Top