Error message setting up base T-2

Glen Thurow

New Member
I installed new firmware (Triumph2_old_3_7_3) on my Triumph 2. Using Javad Mobile for Android I set the parameters for the job (static base). When I try and activate the base I get the following message: "Can't create receiver File ". Is there a setting I'm overlooking? Thanks for the help.
 

David M. Simolo

Well-Known Member
Hi Glen, welcome aboard.

I am far from an expert but when I hook up to my T2 I use Javad's Netview & Modem software. I don't know if that would make any difference for you. I'm sure someone more knowledgeable will jump on here in the near future.
 

Glen Thurow

New Member
Clearing NVRAM on Triumph 2- Hold power and record buttons until all lights flashing then release record button. Do I have that correct?
 

Glen Thurow

New Member
Cleared NVRAM- Still can't create receiver file. The T-2 is collecting and a log file shows increasing data size. However, I'm not getting the survey screen showing the number of epochs collected and time remaining. I've also tried using NetBrowser and receive a similar error message when initiating the static survey.
 

David M. Simolo

Well-Known Member
You probably cleared the NVRAM by what you did from the sounds of things. As I understand it the correct procedure is:
With the unit off hold down the record button
Turn on the unit by hitting the power button once--continue to hold onto the record button
Within usually 10 seconds most of the lights will start a quick flash of an orange color, at which point you can let go of the record button and should be done with the procedure.
 

Glen Thurow

New Member
Thanks, David....I'm still unable to create a receiver file even after clearing the NVRAM. Any other suggestions greatly appreciated. I've tried downloading Netview & modem software but the Javad site is not responding. I see from forum threads that others have had similar problems. I've tried disabling all firewalls, etc. but no success. Perhaps it's temporarily down. I'll try again later.
 

Glen Thurow

New Member
I installed new firmware (Triumph2_old_3_7_3) on my Triumph 2. I believe it was a successful update. I'm also having trouble getting Netview to connect as well. I followed the correct connection scenario. Window recognizes the T-2 and indicates the device is good to go. The driver shows as up to date when I try and update. I've not used the equipment for a while due to health reasons. I am fully recovered now but apparently being sick also made me stupid. As you can see below when I try and connect with either port, it runs through the baud rates and then gives me a receiver not found message.
Javad Netview.PNG
 

Matt Johnson

Well-Known Member
5PLS
Did you try clicking the refresh icon in Netview & Modem? If the USB driver is installed you should see one of COM ports listing "GNSS Receiver":

1525727814031.png



Are you able to start logging files using the record hardware button on the T2? If not, I would suggest you "Initialize the File System" on it:

1525727983817.png
 

Glen Thurow

New Member
Matt...I see you have version 2.0.3.2. I am running 1.1.6.6. That could be part of my problem. The download link on the Javad site for Netview is not responding. Can you send me a link for 2.0.3.2?
 

Matt Johnson

Well-Known Member
5PLS
You should be connect and use the version of Netview and Modem you have. It should also automatically update to the latest version when you launch it. The USB driver must be installed however. Have you installed it?
 

Glen Thurow

New Member
I've updated Netview and Modem to 2.0.3.2. I'm still unable to connect. I believe the driver is up-to-date. Here are some screen shots.
Driver_T2.PNG

Dr_1.PNG

Dr_2.PNG

Dr_3.PNG

I'm not sure. Maybe my board is defective.
 
Top