Triumph-2 and HPT401BT

[Adam]

Use the LS.

In the External Radio Pairing screen I reads the radio info, and automatically goes to pairing. I dont see where it goes thru an unpairing process, maybe this is done in the background. Once the pairing process is completed, radio successfully paired displays. Tap OK and base setup is displayed and connecting on the right side to the t2 and on the left all parameters are yellow, but N/A and no connection. After about 5 seconds I get the warning but this time the text is doubled like this...........External radio is not connected to GNSS receiver
External radio is not connected to GNSS receiver.........

 

[Adam]

To unpair then you will need to switch your radio from slave to master (or vise versa I don't remember which one it is currently set on) in ModemVU. Once this has been done then the standard pairing process in the LS will work to pair the two again.

I seen your previous post about that but thought the process had been improved to allow unpairing/pairing in the field. I will switch it. Thanks

 

[Matt Johnson]

My question is why would have the T2 lost its pairing? Do they do a reset on the Triumph 2 when they are in for this replacement?

My guess would be that they paired it to another radio to test it.

 

[Adam]

To unpair then you will need to switch your radio from slave to master (or vise versa I don't remember which one it is currently set on) in ModemVU. Once this has been done then the standard pairing process in the LS will work to pair the two again.

That did the trick, Thanks


Edit: It allowed the radio to show up when I try to pair via bluetooth and still says it pairs them but no connection in the uhf box.

 

[Adam]

I tried unpairing in Netview with success, but when I tried to pair the two in NetView I get an error. I went in and changed the BT to slave (it was set to master) and tried, but no luck. What am I doing wrong?

 

[Adam]

I cant get a successful pairing thru netview or the LS. Any idea what I need to do?

 

[Adam]

The LS is finding the radio okay

pairing okay

paired

After pairing

 

[Matt Johnson]

Did you try clearing the NVRAM on your T2 yet?

 

[Adam]

A couple of times.

 

[Matt Johnson]

If they are paired correctly the Bluetooth led on the T2 should turn solid blue when the radio is on and Base/Rover Setup is not connected to the T2. Is this happening?

 

[Adam]

If they are paired correctly the Bluetooth led on the T2 should turn solid blue when the radio is on and Base/Rover Setup is not connected to the T2. Is this happening?

No blue light on the t2. Shawn gave me Vladimirs info to troubleshoot with him. I still am operable with TCP where I am today. Thanks Matt

 

[Adam]

Here's a wild pitch but I noticed External UHF not selected in Udate, Apps Settings screen. Could that be causing my problems? I dont recall unchecking it, Shouldnt the default be checked?

 

[Shawn Billings]

I noticed that on mine this morning too. I don't know if I've ever had it checked. Can't hurt, but I don't have a lot of confidence in this being your issue...

 

[Matt Johnson]

Here's a wild pitch but I noticed External UHF not selected in Udate, Apps Settings screen. Could that be causing my problems? I dont recall unchecking it, Shouldnt the default be checked?

This wouldn't be the problem. Can you post a screenshot of the Bluetooth settings in Netview:

 

[Adam]

the I i the current address of bluetooth b is unknown on mine and input mode is cmd

 

[Matt Johnson]

Change the input mode to none and see if it connects after you press Apply.

 

[Matt Johnson]

I don't think that is the problem... post the BT tab from ModemVU:

 

[Adam]

 

[Adam]

Change the input mode to none and see if it connects after you press Apply.

No change.

 

[Matt Johnson]

Try changing the pin to "0000" in NetView.