Bruce Dawson
Active Member
Alexey, this is where I sent the file: http://storage.javad.com/
Base got bumped off point
- Thread starter Bruce Dawson
- Start date
Can you wait till Monday? I'll grab file from javad.storage when I will be back to office. It's impossible to do this from my home.
Bruce Dawson
Active Member
Sure Alexey. I can wait. Thanks!
Eugene Aksyonov
Well-Known Member
sorry, Bruce, try again, please, settings were not applied last time...
Eugene Aksyonov
Well-Known Member
It had to return the uploaded file link after submitting of the file. This link you can put here also.
Bruce Dawson
Active Member
Hmmm, still no go Eugene. Still gives me the "File too large" error.
Eugene Aksyonov
Well-Known Member
test
I believe there are separate restrictions for forums members who aren't in the 5PLS group.
Eugene Aksyonov
Well-Known Member
I have found uploaded file on server. here it is attached. I have recovered it by the time in header
rcv={3W05K9XXSS0083VSU9QW6AHDAY,TRIUMPH2,12288, 0d00h06m38s,@37
should be this one.
rcv={3W05K9XXSS0083VSU9QW6AHDAY,TRIUMPH2,12288, 0d00h06m38s,@37
should be this one.
Eugene Aksyonov
Well-Known Member
Yes, Matt, Group's policies overrides attachment size also. I have fixed it too, now.
Bruce Dawson
Active Member
Now we are talking! Alexey, here you go and many thanks!
Phillip Lancaster
Active Member
What if Javad receivers in the future had electronic levels like the LS, that would be a great monitoring system to tell the rover that it needs to be checked when out of level.
Eugene Aksyonov
Well-Known Member
Phillip, we have this support in T-2 and T-1M. And Triumph-LS can alert you that Base is moved or felt down...
It seems we have to pay more attention to features promottion
It seems we have to pay more attention to features promottion
1. It happened between 22:15:30 and 22:16:30. The movement continued during about 1 minutes. See picture below. Base file 'Base4_120637.jps' has been processed as kinematic epoch by epoch relative to SOPAC site SPUD(4.5 km towards NW).
2. I have splitted Base4_120637.jps into two files: 19:06:57(begin time) - 22:15:30 and 22:16:30 - 23:00:32(end time). I submitted first file to DPOS.
DPOS report is in attachment. Second file is a bit short to be processed well with respect to CORS, that are about 100 km away.
I processed SPUD relative to CORS and adjust network. Than I processed both base files with respect to SPUD. Adjustment report attached.
2. I have splitted Base4_120637.jps into two files: 19:06:57(begin time) - 22:15:30 and 22:16:30 - 23:00:32(end time). I submitted first file to DPOS.
DPOS report is in attachment. Second file is a bit short to be processed well with respect to CORS, that are about 100 km away.
I processed SPUD relative to CORS and adjust network. Than I processed both base files with respect to SPUD. Adjustment report attached.
Great work Alexey!
Sean Joyce
Well-Known Member
Phillip, we have this support in T-2 and T-1M. And Triumph-LS can alert you that Base is moved or felt down...
It seems we have to pay more attention to features promottion
Once again from my previous post.
"I would like to propose a new section/window on this USERS forum where there would be DETAILED complete up-to-the minute information about any software updates/changes/known glitches for the L.S., T2, radios, manuals, new videos, etc., etc.
Could be in the form of a streaming news banner or list and then a click/link for more information on a topic from Javad.com.
I like many here I believe am not using a fraction the many new features and information for Javad equipment because I don't know about them.
I don't go to the Javad website as much as I should and go here much more often. Posting the info here would get it disseminated to the USERS and probably save the Mag 7 lots of time answering redundant questions."
Bruce Dawson
Active Member
Alexey, you are the man! I am going out today to field verify the points collected at that point in time. I would love to know where to look and/or what settings to change to be informed at the LS of a base shift like this.
I've never heard of this feature either. We've discussed it in the past, but I never knew it was implemented.
Nate The Surveyor
Well-Known Member
Sean is right... we need info. Shawn, this is one of those deals where we need more communication, between users and developers.
I like the idea of keeping users in the loop.
N
I like the idea of keeping users in the loop.
N
I'm not sure that there is a loop on this one.