Good news

Vladimir Zhukov

Vladimir Zhukov

Well-Known Member
JAVAD GNSS
John Thompson said:
Vladimir,
I get no response to any command that I enter in the GREIS Commands tab.
View attachment 10265
If I try to enter the commands in the bottom of the Parameters window in the format you specify, the set command returns
ER01A%1%{2,,value out of range}
The reset command appears to reboot the T2, and the print command returns 1575 OK.


My receiver firmware and board are as shown here.
View attachment 10266
I upgraded T2 firmware this morning to 3.7.9. Is 4.0 available?
Click to expand...
You have already BDS in tracking! Congratulations! see you satellite tracking tab
 
John Thompson

John Thompson

Well-Known Member
Vladimir Zhukov said:
You have already BDS in tracking! Congratulations! see you satellite tracking tab
Click to expand...

Vladimir,
Thanks for your replies. I see in the Netview screen shot I posted earlier that the T2 is tracking BDS and GAL. Looks like the RTK info from those constellations is not getting to the T-LS. I set transmit format to RTCM 3.2 MSM3 Short. The GNSS status of the T-LS rover looks like this.
GNSS-STATUS_20200806-12.05.10.png
But the T-2 remote base GNSS status looks like this.
GNSS-STATUS_20200806-12.05.48.png
What else needs enabled?
 
Vladimir Zhukov

Vladimir Zhukov

Well-Known Member
JAVAD GNSS
John Thompson said:
Vladimir,
Thanks for your replies. I see in the Netview screen shot I posted earlier that the T2 is tracking BDS and GAL. Looks like the RTK info from those constellations is not getting to the T-LS. I set transmit format to RTCM 3.2 MSM3 Short. The GNSS status of the T-LS rover looks like this.
View attachment 10270
But the T-2 remote base GNSS status looks like this.
View attachment 10271
What else needs enabled?
Click to expand...

Hi John,
it looks like some issue of J-Field representation maybe because this is an unknown configuration for software.
This could be corrected later.
Just ignore this info and start your T-2 base,
initially two engines RTK did not use BDS and GAL, but after a long click on the Reset Engines button in the Two Engine RTK screen it started to use new signals,
for example, I had a first engine fixed with GPS, GAL, BDS and second with GPS, GLO, BDS
Anyway, if these hints would not work for you, maybe the best option would be to wait for a week or so till J-Field with such support is released
 
Vladimir Zhukov

Vladimir Zhukov

Well-Known Member
JAVAD GNSS
It seems you did not enable it in all places. please confirm for BDS system signals B1 and B1C also checked in N&M?
 
Vladimir Zhukov

Vladimir Zhukov

Well-Known Member
JAVAD GNSS
Hello Nate.

It would be good to check settings of your T2 remotely

if you are ok with an idea, then

1. Download JSupport program from the link: http://get.teamviewer.com/javadgnss
2. Run the program from PC, connected to the Internet.
3. Wait some seconds until red cross in the program window changes to white check-mark on the green.
4. post in this thread the ID-number that program generates for your PC.

T2 please connect to this PC via USB.

Regards,
Vladimir
 
Nate The Surveyor

Nate The Surveyor

Well-Known Member
I'm sitting in a lawn chair. In my yard. Laptop is hooked up to power, internet, and t-2. It's starting to rain.
Can I move back inside, or do you want skyview?
:))
 
Vladimir Zhukov

Vladimir Zhukov

Well-Known Member
JAVAD GNSS
Hi Nate,
Thank you for giving access to your receiver.
You had firmware from 2017 and OAF with not enabled BDS B1CI
It should be ok now
 
You must log in or register to reply here.
Top